客服QQ:

675609587

邮箱地址:

675609587@qq.com

电话:13280489678

手机:13280489678

> 新闻中心 > 技术资料 >

摇臂钻床操作技巧,快速上手操作的办法

2020-09-02 21:29来源:未知浏览:

摇臂钻床操作技巧,快速上手操作的办法

 

更好的操作摇臂钻床技巧:

 

1、摇臂钻床工件装夹必须牢固可靠。钻削小工件时,应用工具夹持,不准用手拿着钻。工作中严禁戴手套。

2、使用自动走刀时,要选好进给速度,调整好行程限位块。手动进刀时,逐渐增加压力或逐渐减小压力,以免用力过猛造成事故。

3、摇臂钻床钻头上缠有长铁屑时,要停车清理,用刷子或铁钩清除,严禁用手拉。

4、精绞深孔、拔锥棒时,不可用力过猛,以免手撞在刀具上。

5、工件材料较硬或钻孔较深时,应在工作过程中不断将钻头抽出孔外,排除钻屑,防止钻头过热并使用冷却润滑液。必要时采用保护性卡头。

6、钻孔时,身体不要离主轴太近,以免头发或衣服被钻头卷入。

7、用钻床绞孔时,绝对不可倒转,否则铰刀和孔壁之间容易挤住刀屑,造成孔壁划伤或刀刃崩裂。

8、使用摇臂钻床摇臂钻时,横臂回转范围内不准站人,不准有障碍物。工作时横臂必须夹紧。

9、摇臂钻床横臂及工作台上不准堆放物件。

10、工件结束时,将横臂降到最低位置,主轴箱靠近主轴,并且要夹紧。

 

 

Better operation skills of radial drilling machine:

1. The rocker arm of the drill must be fixed firmly and reliably. When drilling small workpieces, it should be clamped with tools. It is not allowed to hold the drill by hand. Do not wear gloves during work.

2. When using the automatic feed, the feed speed should be selected and the travel limit block should be adjusted. When manually feeding, gradually increase or decrease the pressure to avoid accidents caused by excessive force.

3. When long iron chips are wrapped on the drill bit of radial drilling machine, stop the machine for cleaning, and use brush or iron hook to remove it. It is strictly forbidden to pull it by hand.

4. Do not use too much force when reaming deep hole and pulling taper rod, so as to avoid hitting the tool by hand.

5. When the workpiece material is hard or the drilling is deep, the drill bit should be continuously pulled out of the hole during the working process to remove the drilling cuttings, prevent the drill bit from overheating and use cooling lubricant. If necessary, use protective clamps.

6. When drilling, the body should not be too close to the main shaft, so as to avoid the hair or clothes being involved by the drill bit.

7. When reaming a hole with a drilling machine, it is absolutely not allowed to turn it upside down, otherwise the cuttings will be squeezed between the reamer and the hole wall, resulting in the scratch of the hole wall or the crack of the blade.

8. When the radial drilling machine is used, people are not allowed to stand in the rotating range of the cross arm and there are no obstacles. The cross arm must be clamped during operation.

9. It is not allowed to stack objects on the cross arm and working table of radial drilling machine.

10. At the end of the workpiece, lower the cross arm to the lowest position, and the spindle box is close to the spindle, and should be clamped.

  • 电话:13280489678
  • 联系人:郑经理
  • 邮箱:675609587@qq.com
  • 地址:山东省滕州市经济开发区
  • 山东沈北数控产品有机械摇臂钻床、液压摇臂钻床、立式钻床、数控钻床、铣床、锯床、液压机等型号机床设备及配件。厂家直接发货质量保证,价格优惠,发货周期短,产品畅销国内及国际市场,得到了越来越多的国内外客户的认可和支持。

微信二维码

Copyright © 山东沈北数控机床有限公司 版权所有 备案号:鲁ICP备20014639号-3