客服QQ:

675609587

邮箱地址:

675609587@qq.com

电话:13280489678

手机:13280489678

> 新闻中心 > 技术资料 >

液压摇臂钻床日常操作注意事项,摇臂钻床操作指南

2020-09-02 21:33来源:未知浏览:

摇臂钻床操作指南

使用注意

1、不能在使用液压摇臂钻床钻孔时用纱布清除铁屑,也不允许用嘴吹或者用手擦拭,应该使用专用工具、刷子。

2、操作摇臂钻床者要认真做到“三好”(①管好、②用好、③修好)“四会”(①会使用、②会保养、③会检查、④会排除故障)。

3、严格按照液压摇臂钻床的润滑图表规定进行加油,做到“五定”(①定时、②定点、③定量、④定质、⑤定人),注好油后应将油杯(池)的盖子盖好。

4、在钻孔前,找正工件位置时,应将锁紧装置松开,进刀主轴伸出长度根据钻孔深度调整合适,然后将各锁紧装置锁紧。

5、在调整钻孔深度的自动走刀时,应先使钻头接触工件,再把进给撞块按要求调到深度数值,并锁紧。

6、操作人员需要注意刀具的锋利,磨钝了的刀具不得继续使用,以防发生意外。

7、工作中液压摇臂钻床的高度应调整适当,不宜过高。在加工过程中,摇臂、主轴箱必须处于夹紧状态。

8、工作后需要将各手柄置于非工作位置上,主轴箱停放应靠近立柱,摇臂适当降低,再切断电源。

9、工件的装卡必须牢固,钻透孔时必须在底面垫上垫块,不然会钻伤设备。

10、在液压摇臂钻床钻孔过程中钻头未退离工件前不得停车。反车时,必须等主轴停止后再开动。

11、装卸工件或夹具时,要将横臂移开,同时注意周围的人及物,以发出碰撞事故

12、停车八小时以上再开动设备时,应先低速运转五分钟,确认润滑系统畅通,各部传动正常后再开始工作。

13、工作中要注意超负荷的现象,如保险结合子脱落或发出响声,应立即停止自动进给,并消除超负荷原因。

14、钻孔时,调整转速必须先停车,严禁不停车变速,否则将打坏变速箱内齿轮。

15、操作液压摇臂钻床的人员必须熟悉本设备结构性能,经考试合格取得操作证后方才能独立操作。

 

 

Operation guide for radial drilling machine

Attention to use

1. It is not allowed to use gauze to remove iron filings, blow with mouth or wipe with hand when drilling with hydraulic radial drilling machine. Special tools and brushes should be used.

2. The operator of radial drilling machine should conscientiously do "three good" (① well managed, ② used, ③ repaired) "four skills" (① able to use, ② to maintain, ③ to be able to check, and ④ to be able to eliminate faults).

3. Oil shall be added in strict accordance with the lubrication chart of hydraulic radial drilling machine to achieve the "five fixed" (① timing, ② fixed point, ③ quantitative, ④ fixed quality, and ⑤ fixed person). After the oil is injected, the cover of the oil cup (pool) shall be covered.

4. Before drilling, when aligning the position of the workpiece, the locking device should be released, the extension length of the feed spindle should be adjusted according to the drilling depth, and then the locking devices should be locked.

5. When adjusting the automatic feed of drilling depth, the drill should first contact the workpiece, then adjust the feed ram to the depth value as required and lock it.

6. If the tool is blunt, it should not be used again.

7. The height of hydraulic radial drilling machine should be adjusted properly, not too high. In the process of machining, the rocker arm and headstock must be in clamping state.

8. After working, the handle should be placed in the non working position, the headstock should be placed close to the column, the rocker arm should be lowered properly, and then the power supply should be cut off.

9. The clamping of the workpiece must be firm, and cushion block must be put on the bottom surface when drilling through hole, otherwise the equipment will be damaged.

10. In the drilling process of hydraulic radial drilling machine, the drill must not be stopped before the drill is withdrawn from the workpiece. When reversing, the spindle must be stopped before starting.

11. At the same time, when loading and unloading the workpiece, the cross arm should be removed

12. When the equipment is stopped for more than eight hours and then started, it should be operated at low speed for five minutes to confirm that the lubrication system is unblocked and that the transmission of each part is normal.

13. Pay attention to the phenomenon of overload in work. If the safety connector falls off or makes a sound, the automatic feed should be stopped immediately and the cause of overload should be eliminated.

14. When drilling, the speed must be adjusted first. It is strictly forbidden to change speed without stopping, otherwise the gear in the gearbox will be damaged.

15. Operators of hydraulic radial drilling machine must be familiar with the structure and performance of the equipment, and can operate independently after passing the examination and obtaining the operation certificate.

  • 电话:13280489678
  • 联系人:郑经理
  • 邮箱:675609587@qq.com
  • 地址:山东省滕州市经济开发区
  • 山东沈北数控产品有机械摇臂钻床、液压摇臂钻床、立式钻床、数控钻床、铣床、锯床、液压机等型号机床设备及配件。厂家直接发货质量保证,价格优惠,发货周期短,产品畅销国内及国际市场,得到了越来越多的国内外客户的认可和支持。

微信二维码

Copyright © 山东沈北数控机床有限公司 版权所有 备案号:鲁ICP备20014639号-3